20 Coolest Rail Stiles

 

Yonico 12241 Rail and Stile Router Bits with Matched 2 Bit Round-Over 12-Inch Shank

Yonico 12241 Rail and Stile Router Bits with Matched 2 Bit Round-Over 1/2-Inch Shank

Yonico 12241 Rail and Stile Router Bits with Matched 2 Bit Round-Over 1/2-Inch Shank - Enhance the inside panel of your stile and rail door with one of our yonico panel raisers. Yonico rail and stile router bit set (12241) will produce rail and stile for cabinet doors in the classic round-over design. Two flute carbide cutters & 1/2″ shanks. Fully enclosed ball bearing guides allow for precise cuts without the use of a fence.

 

Rockler Classical Reversible Rail Stile Bit

Rockler Classical Reversible Rail & Stile Bit

Rockler Classical Reversible Rail & Stile Bit - Groove is 3/8″d x 1/4″h. 5/8″ bearing. Stack the bit (starting from the shank end) as follows straight cutter, bearing, then profile cutter. For those who make cabinet doors only occasionally, this cutter provides an affordable, space-saving solution to routing cope and stick joints.  Available in chamfer, ogee and classical styles (27190, 23422 and 27602, respectively). One bit cuts both rail and stile profiles just remove the cutters and rearrange them to go from coping rail ends to routing grooves in the stiles. Stack the bit (starting from the shank end) as follows profile cutter, straight cutter, then bearing. Because the bit is bearing-guided, you can also rout arched rails without a template or fence. Instructions for routing to cut the groove and profile on the insides of the rails and stiles, run stock face down on table. 1-5/8″ diameter x 15/16″ cutter height x 1/2″ shank. Important safety note do not invert any of the cutters be sure the carbide is facing the right direction for the rotation of the router. To cope the ends of the rails, run stock face up on table.

 

Router Bit Set-Up Jigs for 91991 Stile and Rail Router Bits

Router Bit Set-Up Jigs for 91991 Stile and Rail Router Bits

Router Bit Set-Up Jigs for 91991 Stile and Rail Router Bits - All jigs are manufactured for 3/4″ stock. ). (Jigs designed for rail-and-stile have the rail cut on one side and the stile cut on the opposing side. They are made of durable hdpe and measure 2″ x 3-7/8″ x 3/4″. This system is ideal for making accurate rail-and-stile construction, lock miter joints and more. Set your router bit to the precise height every time simply bring the router bit up through the table and align the jig with the cutting edge of the bit.

 

Freud EC-260 Beading Profile Shaper Cutter Set For 34-Inch Rail And Stile Doors - 34 Bore

Freud EC-260 Beading Profile Shaper Cutter Set For 3/4-Inch Rail And Stile Doors – 3/4 Bore

Freud EC-260 Beading Profile Shaper Cutter Set For 3/4-Inch Rail And Stile Doors – 3/4 Bore - Covered by freud’s limited lifetime warranty. Kickback reducing design. Thick micrograin carbide tips.

 

Yonico 12247 2 Bit Rail and Stile Router Bit Set with Bevel 12-Inch Shank

Yonico 12247 2 Bit Rail and Stile Router Bit Set with Bevel 1/2-Inch Shank

Yonico 12247 2 Bit Rail and Stile Router Bit Set with Bevel 1/2-Inch Shank - . The yonico 12247 rail and stile router bit set will cut rail and stile for cabinet doors in a contemporary bevel design. Yonico router bits are manufactured with solid hardened steel bodies and c3 micrograin carbide for professional, efficient routing. Two flute carbide cutters & 1/2″ shanks. Fully enclosed ball bearing guides allow for precise cuts without the use of a fence. Use with up to 7/8″ stock.

 

Woodtek 821047 Router Bits Door Construction Stile Rail - Cabinet Rail Stile Set Cove Bead Detail 12 Shank

Woodtek 821047, Router Bits, Door Construction, Stile & Rail – Cabinet, Rail & Stile Set, Cove & Bead Detail, 1/2″ Shank

Woodtek 821047, Router Bits, Door Construction, Stile & Rail – Cabinet, Rail & Stile Set, Cove & Bead Detail, 1/2″ Shank - Micro-grain carbide cutting surfaces have been diamond honed to 800 grit for minimal tear-out and smoother surface quality. 001″ tolerances and dynamic balancing help ensure vibration-free operation. Cope and stick joinery for cabinet doors. The single piece design of this woodtek® carbide-tipped cove and bead with fillet stile and rail router bit set makes set-up more accurate, faster and easier, use with table-mounted portable routers rugged ptfe (polytetrafluoroethylene) briteviewâ„¢ coating not only protects but the bright yellow color provides better visibility for safer operations. Cnc-machining to +/-0. Manufactured in facilities meeting stringent iso 90002000 quality assurance standards. Imported. Positive shear angle places less demand upon your routing equipment.

 

Infinity Tools 91-522 12 Shank Interior Exterior Door Making Rail Stile Router Bit Set Ogee Profile

Infinity Tools 91-522, 1/2″ Shank Interior & Exterior Door Making Rail & Stile Router Bit Set, Ogee Profile

Infinity Tools 91-522, 1/2″ Shank Interior & Exterior Door Making Rail & Stile Router Bit Set, Ogee Profile - . This heavy duty set produces a 7/16″ wide profile. Save $$ by making your own doors with this versatile system that comes with both 1/4″ and 1/2″ kerf slot cutters for making doors out of 1-3/8″ or 1-3/4″ stock. Building 1-3/8″ interior or 1-3/4″ exterior-facing doors has never been easier than with the help of this specially designed 2-piece door set.

 

CMT 89150211 2-Piece Rail Stile Bit Set 12-Inch Shank 1-34-Inch Diameter Carbide-Tipped

CMT 891.502.11 2-Piece Rail & Stile Bit Set, 1/2-Inch Shank, 1-3/4-Inch Diameter, Carbide-Tipped

CMT 891.502.11 2-Piece Rail & Stile Bit Set, 1/2-Inch Shank, 1-3/4-Inch Diameter, Carbide-Tipped - 2 sinterhip hi-density industrial chrome carbide cutting edges for long-lasting performance. Make rail and stile joints to buid your own doors use on router tables only. Clean, precise and well-crafted for strength ideal for jobs requiring perfectly matching profiles. Cmt bits were rated the best overall in comparison to other brand (test by wood magazine). Male & female bits for material from 23/32 to 7/8-inch thick 2-51/64-inch overall length.

 

YaeTek Rail Stile Router Bit Set - Shaker 2 Pc 12 Shank

YaeTek Rail & Stile Router Bit Set – Shaker 2 Pc. 1/2″ Shank

YaeTek Rail & Stile Router Bit Set – Shaker 2 Pc. 1/2″ Shank - Our router bits are manufactured using solid hardened steel and c3 micro grain carbide. Precise, designer profiles create smooth and detailed cuts, perfect for projects of any level of complexity. (C3 grade carbide is the highest grade used in the router bit industry) the result is a highly durable bit that can be utilized for the most rigorous industrial applications. Our bits are the preferred choice of professionals and hobbyists alike.

 

Freud Premier Adjustable Rail Stile Bit with 12 Shank - Round Over Bead Profile 99-763

Freud Premier Adjustable Rail & Stile Bit with 1/2″ Shank – Round Over Bead Profile (99-763)

Freud Premier Adjustable Rail & Stile Bit with 1/2″ Shank – Round Over Bead Profile (99-763) - Ticotm hi-density carbide to maximize bit life and material finish. Unique cutter geometry to eliminate tearout. Patented extended tenon capability, top portion of cutter, including bearing and spindle, is removed to produce the front of the long tenon profile. Cuts all composition materials, plywoods, hardwoods, and softwoods. Ideal material thickness 5/8″ to 1-1/4″ stock.

 

Traditional Stile and Rail Router Bit Set

Traditional Stile and Rail Router Bit Set

Traditional Stile and Rail Router Bit Set - Rockler rail and stile bit sets are manufactured to exacting standards and create perfectly matched cope and stick joints. Baked-on anti-stick coating to reduce pitch and resin buildup. K10 and k20 grade carbide for clean cutting action. Final sharpening with 600, 800 grit diamond wheels. With ball bearing guide, you can even use a template to build doors with curving rails. If you are not 100% satisfied with these bits, send them back for a refund. The one-piece cutting edge allows you to achieve a perfect fit without having to disassemble an arbor and install shims. 5/8″ bearing. . Use this rail and stile router bit set to create beautiful door frames for glass panel, flat panel and raised panel doors. 1/4″ x 3/8″ groove. Precision balanced for smooth operation.

 

Yonico 12249 Rail and Stile Router Bit Set with 12-Inch Shank 2-Piece

Yonico 12249 Rail and Stile Router Bit Set with 1/2-Inch Shank, 2-Piece

Yonico 12249 Rail and Stile Router Bit Set with 1/2-Inch Shank, 2-Piece - Solid hardened steel bodies with anti-kickback design. Satisfaction guaranteed and lifetime warranty. Build-up & heat resistant teflon coating. Build-up and heat resistant teflon coating. C3 micro-grain tungsten carbide cutters. Industrial quality router bits. Satisfaction guaranteed & lifetime warranty.

 

BQLZR 12 Inch Shank 516 Inch Slot Width Cemented Carbide Rail Stile Finger Joint Glue Router Bit Cone Tenon Woodwork Cutter

BQLZR 1/2 Inch Shank 5/16 Inch Slot Width Cemented Carbide Rail & Stile Finger Joint Glue Router Bit Cone Tenon Woodwork Cutter

BQLZR 1/2 Inch Shank 5/16 Inch Slot Width Cemented Carbide Rail & Stile Finger Joint Glue Router Bit Cone Tenon Woodwork Cutter - Woodworking tools,suitable for use of trimming machine 4. 38 inch cutter height 21mm / 0. Every product has a unique manufacturing part number label on the inner package that proves it has been qualified,which include part number,model number and inspection date information 2. Feature 1. 42 x 1. Perfect choice of professionals and hobbyists specification materialcemented carbide color silver & yellow brand name bqlzr shank dia 1/2 inch slot width 5/16 inch cutter width 35mm / 1. 83 inch size 87 x 35 mm / 3. 38 inch (l x w ) weight132g package include 1 x cone tenon router bit. If you have any questions about the item,please provide us the manufacturing part number for checking,your profits will be guaranteed. 3. Cemented carbide constructed,1/2 inch shank diamater and 5/16 inch slot width 5.

 

Yonico 12337 Rail and Stile Panel Raiser Router Bit Set with Large Ogee 12-Inch Shank 3-Piece

Yonico 12337 Rail and Stile Panel Raiser Router Bit Set with Large Ogee 1/2-Inch Shank, 3-Piece

Yonico 12337 Rail and Stile Panel Raiser Router Bit Set with Large Ogee 1/2-Inch Shank, 3-Piece - Ball bearing guides allow for precise cuts without the use of a fence. Set comes in a solid wood storage case. The 3-1/2″ diameter panel raiser bit will put a large ogee edge on the central panel of your door. All yonico router bits are manufactured with c3 carbide cutters providing multiple hard core use. Large rail and stile cabinet doors are easy to make with this yonico 12337 raised panel cabinet door router bit set. The large 1-3/4″ diameter rail & stile router bits create a perfectly matched ogee door frame. Two flute carbide cutters & 1/2″ shanks. Use this set with up to 7/8″ stock. The panel raiser router bit can also be used to make attractive drawer fronts, table tops, plaques and moldings. Included in this set large ogee panel raiser router bit, 2 bit matched large ogee rail & stile router bits, allen wrench plus extra spacers, solid wood storage case.

 

Woodtek 820739 Router Bits Door Construction Stile Rail - Cabinet Reversible Rail-Stile Bit Cove-Bead Detail12 Shk

Woodtek 820739, Router Bits, Door Construction, Stile & Rail – Cabinet, Reversible Rail-Stile Bit Cove-Bead Detail1/2″ Shk

Woodtek 820739, Router Bits, Door Construction, Stile & Rail – Cabinet, Reversible Rail-Stile Bit Cove-Bead Detail1/2″ Shk - Manufactured in facilities meeting stringent iso 90002000 quality assurance standards. . Micro-grain carbide cutting surfaces have been diamond honed to 800 grit for minimal tear-out and smoother surface quality. Woodtek® carbide-tipped reversible stile and rail router bits produce perfectly matching joints for stile and rail construction and general edge joining, use with table-mounted portable routers rugged ptfe (polytetrafluoroethylene) briteviewâ„¢ coating not only protects but the bright yellow color provides better visibility for safer operations. 001″ tolerances and dynamic balancing help ensure vibration-free operation. Shaker, bead & cove, ogee, and ogee with fillet patterns. 1/2″ shanks. Imported. Positive shear angle places less demand upon your routing equipment. Cnc-machining to +/-0.

 

MLCS 11009 Katana Round Over Matched Rail and Stile Shaper Cutter 2-Piece Set

MLCS 11009 Katana Round Over Matched Rail and Stile Shaper Cutter, 2-Piece Set

MLCS 11009 Katana Round Over Matched Rail and Stile Shaper Cutter, 2-Piece Set - Precise, reliable woodworking. 1/2-inch reducer bushings included. Life time guarantee. Tungsten micro-carbide tipped, diamond honed. 2-piece matched set.

 

Yonico 12343 Round Over Rail and Stile with Cove Panel Raiser 3 Bit Router Bit Set 12-Inch Shank

Yonico 12343 Round Over Rail and Stile with Cove Panel Raiser 3 Bit Router Bit Set 1/2-Inch Shank

Yonico 12343 Round Over Rail and Stile with Cove Panel Raiser 3 Bit Router Bit Set 1/2-Inch Shank - Industrial quality router bits. Build-up and heat resistant teflon coating. Build-up & heat resistant teflon coating. Satisfaction guaranteed & lifetime warranty. C3 micro-grain tungsten carbide cutters. Satisfaction guaranteed and lifetime warranty. Solid hardened steel bodies with anti-kickback design.

 

Yonico 12201 Rail and Stile Plywood Conversion Kit for 52mm Plywood

Yonico 12201 Rail and Stile Plywood Conversion Kit for 5.2mm Plywood

Yonico 12201 Rail and Stile Plywood Conversion Kit for 5.2mm Plywood - The rail and stile bits must be purchased separately. . Standard rail & stile router bits create 1/4″ grooves for the center panel. This conversion kit allows 1/4″ plywood (actual 5. 5mm plywood use yonico 12202 rail & stile conversion kit. (For 5. ) Note this kit contains the 2 blades only. When using 1/4″ plywood for the panel, 1/4″ grooves will be too large as 1/4″ plywood is finished down to slightly less than 1/4″. This set is compatible with • yonico 12241 • yonico 12243 • yonico 12243q • yonico 12249 • yonico 12335 • yonico 12336 • yonico 12338 • yonico 12343 • yonico 12345 • yonico 12350 • yonico 12432. 2mm) to be used as center panels for rail & stile doors. The yonico 12201 rail and stile conversion kit to replaces the existing groove cutters on your yonico rail & stile router bit set.

 

Agile-Shop 2pcs Rail Stile Router Bit Set with 12 inch Shank Shaker for Woodworking

Agile-Shop 2pcs Rail & Stile Router Bit Set with 1/2 inch Shank Shaker for Woodworking

Agile-Shop 2pcs Rail & Stile Router Bit Set with 1/2 inch Shank Shaker for Woodworking - For up to 7/8″ stock. Materials body, solid hardened steel blade, industrial grade micro grain carbide package includes 2 x router bits. 1/2″ shanks. Create your own beautiful shaker style cabinet doors using rail & stile router bit set.

 

MLCS Cabinet Door 6 Piece Rail and Stile Shaper Cutter Set--Round Over Profile

MLCS Cabinet Door 6 Piece Rail and Stile Shaper Cutter Set–Round Over Profile

MLCS Cabinet Door 6 Piece Rail and Stile Shaper Cutter Set–Round Over Profile - Set includes round over stile, 1/2″ straight, 1/4″ straight, rail for round over stile, 1/2″ straight, 1/4″ straight. For stock sizes 3/4″ to 1-1/4″. 3/8″ depth of cut. 2-7/8″ large diameter. Fits both 1/2″ and 3/4″ spindles. Versatile 3-in-1 shaper cutters make rail and stile doors with wood and glass panels, as well as tongue and groove joints.