21 Greatest Spiral Flute Taps for 2020

 

YG-1 F8 Series Vanadium Alloy HSS Spiral Flute Tap TiN Coated Round Shank with Square End Bottoming Chamfer 34-16 Thread Size H5 Tolerance

YG-1 F8 Series Vanadium Alloy HSS Spiral Flute Tap, TiN Coated, Round Shank with Square End, Bottoming Chamfer, 3/4″-16 Thread Size, H5 Tolerance

YG-1 F8 Series Vanadium Alloy HSS Spiral Flute Tap, TiN Coated, Round Shank with Square End, Bottoming Chamfer, 3/4″-16 Thread Size, H5 Tolerance - Titanium nitride coatings add a hard layer of gold-colored ceramic to the surface that extends tool life and permits faster cutting speeds than uncoated tools. Round shanks allow use with a wide variety of toolholding systems. 121875-inches thread length. High-speed steel tools are good for most general purpose applications, offering a combination of hardness and toughness for wear resistance. When run in a counterclockwise direction (right-hand cut) spiral fluted tools evacuate chips up and out of the cut to reduce clogging.

 

YG-1 F4 Series Vanadium Alloy HSS Spiral Flute Tap Steam Oxide Round Shank with Square End Bottoming Chamfer 516-18 Thread Size H5 Tolerance

YG-1 F4 Series Vanadium Alloy HSS Spiral Flute Tap, Steam Oxide, Round Shank with Square End, Bottoming Chamfer, 5/16″-18 Thread Size, H5 Tolerance

YG-1 F4 Series Vanadium Alloy HSS Spiral Flute Tap, Steam Oxide, Round Shank with Square End, Bottoming Chamfer, 5/16″-18 Thread Size, H5 Tolerance - Round shanks allow use with a wide variety of toolholding systems. When run in a counterclockwise direction (right-hand cut) spiral fluted tools evacuate chips up and out of the cut to reduce clogging. Black oxide treatment adds lubricity and creates small pockets on the surface of the tool that act to hold coolant near the cutting edge. High-speed steel tools are good for most general purpose applications, offering a combination of hardness and toughness for wear resistance. 06875-inches thread length.

 

YG-1 F8 Series Vanadium Alloy HSS Spiral Flute Tap TiN Coated Round Shank with Square End Bottoming Chamfer 38-16 Thread Size H3 Tolerance

YG-1 F8 Series Vanadium Alloy HSS Spiral Flute Tap, TiN Coated, Round Shank with Square End, Bottoming Chamfer, 3/8″-16 Thread Size, H3 Tolerance

YG-1 F8 Series Vanadium Alloy HSS Spiral Flute Tap, TiN Coated, Round Shank with Square End, Bottoming Chamfer, 3/8″-16 Thread Size, H3 Tolerance - Round shanks allow use with a wide variety of toolholding systems. Titanium nitride coatings add a hard layer of gold-colored ceramic to the surface that extends tool life and permits faster cutting speeds than uncoated tools. 075-inches thread length. When run in a counterclockwise direction (right-hand cut) spiral fluted tools evacuate chips up and out of the cut to reduce clogging. High-speed steel tools are good for most general purpose applications, offering a combination of hardness and toughness for wear resistance.

 

YG-1 G4 Series Vanadium Alloy HSS Spiral Flute Tap Uncoated Bright Finish Round Shank with Square End Bottoming Chamfer M6-1 Thread Size D5 Tolerance

YG-1 G4 Series Vanadium Alloy HSS Spiral Flute Tap, Uncoated (Bright) Finish, Round Shank with Square End, Bottoming Chamfer, M6-1 Thread Size, D5 Tolerance

YG-1 G4 Series Vanadium Alloy HSS Spiral Flute Tap, Uncoated (Bright) Finish, Round Shank with Square End, Bottoming Chamfer, M6-1 Thread Size, D5 Tolerance - When run in a counterclockwise direction (right-hand cut) spiral fluted tools evacuate chips up and out of the cut to reduce clogging. Uncoated tools feature just the base substrate without any additional treatment or coatings and are suitable for a wide range of applications. 0625-inches thread length. Round shanks allow use with a wide variety of toolholding systems. High-speed steel tools are good for most general purpose applications, offering a combination of hardness and toughness for wear resistance.

 

Morse Cutting Tools 36176 Spiral Flute Taper Pipe Taps High-Speed Steel Bright Finish NPTF Thread 4 Flutes 12-14 Size

Morse Cutting Tools 36176 Spiral Flute Taper Pipe Taps, High-Speed Steel, Bright Finish, NPTF Thread, 4 Flutes, 1/2″-14″ Size

Morse Cutting Tools 36176 Spiral Flute Taper Pipe Taps, High-Speed Steel, Bright Finish, NPTF Thread, 4 Flutes, 1/2″-14″ Size - The spiral flute lifts the chips out of the hole to eliminate chip packing. Spiral flute taper pipe taps are recommended for tapping string and ductile materials that produce long stringy chips. Nptf threads are used for applications requiring a tight seal without the use of thread sealants.

 

12-24 UNC Spiral Flute Tap Bottom GH3 Limit 2 Flute HSS Uncoated Bright Finished Ground Thread Luctool Provides Premium Quality Hand Tools for Metal Threading

12-24 UNC Spiral Flute Tap Bottom GH3 Limit 2 Flute HSS Uncoated Bright Finished Ground Thread. Luctool Provides Premium Quality Hand Tools for Metal Threading.

12-24 UNC Spiral Flute Tap Bottom GH3 Limit 2 Flute HSS Uncoated Bright Finished Ground Thread. Luctool Provides Premium Quality Hand Tools for Metal Threading. - Our tools are widely applied on metal cutting, home improvement, thread repairing and construction. Prompt shipping from us warehouse. Luctool provides threading tools including taps, dies and related products. Making our hardworking people happy with tools having premium quality and reasonable price. Satisfaction guarantee–60 days money back your satisfaction is always our priority.

 

M3 M4 M5 M6 M8 Titanium Coated HSS Spiral Flute Metric Tap Set 5Pcs

M3 M4 M5 M6 M8 Titanium Coated HSS Spiral Flute Metric Tap Set 5Pcs

M3 M4 M5 M6 M8 Titanium Coated HSS Spiral Flute Metric Tap Set 5Pcs - Spiral tap the crumbs into a spiral up chip evacuation, it is more suitable for the processing of blind holes and sticky materials processing. Features spiral groove, can tap to the lowest part of the blind hole, no residual cutting, good chip removal effect, fast cutting, easy to enter the bottom hole. Applicable material suitable for wood, aluminum, iron, thin stainless steel. Included 5pcs of m3, m4, m5, m6, m8 titanium plated spiral tap, made of hss 6542. Use to cut continuously curved material, blind hole processing, hole with an axial groove.

 

YG-1 F4 Series Vanadium Alloy HSS Spiral Flute Tap Steam Oxide Round Shank with Square End Bottoming Chamfer 10-32 Thread Size H3 Tolerance

YG-1 F4 Series Vanadium Alloy HSS Spiral Flute Tap, Steam Oxide, Round Shank with Square End, Bottoming Chamfer, 10-32 Thread Size, H3 Tolerance

YG-1 F4 Series Vanadium Alloy HSS Spiral Flute Tap, Steam Oxide, Round Shank with Square End, Bottoming Chamfer, 10-32 Thread Size, H3 Tolerance - 05-inches thread length. High-speed steel tools are good for most general purpose applications, offering a combination of hardness and toughness for wear resistance. When run in a counterclockwise direction (right-hand cut) spiral fluted tools evacuate chips up and out of the cut to reduce clogging. Black oxide treatment adds lubricity and creates small pockets on the surface of the tool that act to hold coolant near the cutting edge. Round shanks allow use with a wide variety of toolholding systems.

 

YG-1 F8 Series Vanadium Alloy HSS Spiral Flute Tap TiN Coated Round Shank with Square End Bottoming Chamfer 516-18 Thread Size H5 Tolerance

YG-1 F8 Series Vanadium Alloy HSS Spiral Flute Tap, TiN Coated, Round Shank with Square End, Bottoming Chamfer, 5/16″-18 Thread Size, H5 Tolerance

YG-1 F8 Series Vanadium Alloy HSS Spiral Flute Tap, TiN Coated, Round Shank with Square End, Bottoming Chamfer, 5/16″-18 Thread Size, H5 Tolerance - When run in a counterclockwise direction (right-hand cut) spiral fluted tools evacuate chips up and out of the cut to reduce clogging. High-speed steel tools are good for most general purpose applications, offering a combination of hardness and toughness for wear resistance. 06875-inches thread length. Titanium nitride coatings add a hard layer of gold-colored ceramic to the surface that extends tool life and permits faster cutting speeds than uncoated tools. Round shanks allow use with a wide variety of toolholding systems.

 

MaxTool 12-13 Spiral Flute Tap 13TPI HSS M2 Fully Ground Right Hand SFF02W02R32

MaxTool 1/2-13 Spiral Flute Tap; 13TPI HSS M2 Fully Ground Right Hand; SFF02W02R32

MaxTool 1/2-13 Spiral Flute Tap; 13TPI HSS M2 Fully Ground Right Hand; SFF02W02R32 - The round shank with square driver makes the taps suitable for hand or power-driven applications. The spiral flutes are suitable for threading through holes and blind or bottoming holes. They are used to create right-hand threads in a range of materials. Maxtool unc and unf uncoated high-speed steel spiral flute taps have spiral flutes and round shanks with square driver. You can always rely on maxtoolmaxtool’s slogan is consistent quality maxtool toolmax. The premium high speed steel material provides long tool life. This uncoated taps can be used on a broad range of materials. Maxtool is a cutting tools distributor in new york to meet a wide range cutting demand of customers in today’s markets, which include automotive, aerospace, electronics, medical, printed circuit boards, optical industries, and moremaxtool maintains the leading spirit in supply of standard and custom-made high performance cutting tools, such as polycrystalline diamond (pcd), polycrystalline cubic boron nitride (pcbn), carbide, high speed steel (hss) tools, hole saws, diamond wheels, etc for machining ferrous, non-ferrous, composite, fiberglass, and carbon fiber materials. It is available in three different ansi standards unc (unified coarse), unf (unified fine), or uns (unified special). We offer our products worldwide, unless otherwise restricted by our suppliersin addition, maxtool offers re-sharpening services and custom tooling solutionsmaxtool warmly welcomes everyone to visit our amazon store, and honestly appreciates everyone very much to give a cooperative chance to discuss your requirementmaxtool will do the best to make each buyer satisfaction.

 

YG-1 F4 Series Vanadium Alloy HSS Spiral Flute Tap Steam Oxide Round Shank with Square End Bottoming Chamfer 38-16 Thread Size H5 Tolerance

YG-1 F4 Series Vanadium Alloy HSS Spiral Flute Tap, Steam Oxide, Round Shank with Square End, Bottoming Chamfer, 3/8″-16 Thread Size, H5 Tolerance

YG-1 F4 Series Vanadium Alloy HSS Spiral Flute Tap, Steam Oxide, Round Shank with Square End, Bottoming Chamfer, 3/8″-16 Thread Size, H5 Tolerance - When run in a counterclockwise direction (right-hand cut) spiral fluted tools evacuate chips up and out of the cut to reduce clogging. Round shanks allow use with a wide variety of toolholding systems. 075-inches thread length. Black oxide treatment adds lubricity and creates small pockets on the surface of the tool that act to hold coolant near the cutting edge. High-speed steel tools are good for most general purpose applications, offering a combination of hardness and toughness for wear resistance.

 

HARKY  F4 Series Vanadium Alloy HSS Spiral Flute Tap Steam Oxide Round Shank with Square End Bottoming Chamfer 516-18 Thread Size H3 Tolerance

HARKY F4 Series Vanadium Alloy HSS Spiral Flute Tap, Steam Oxide, Round Shank with Square End, Bottoming Chamfer, 5/16″-18 Thread Size, H3 Tolerance

HARKY F4 Series Vanadium Alloy HSS Spiral Flute Tap, Steam Oxide, Round Shank with Square End, Bottoming Chamfer, 5/16″-18 Thread Size, H3 Tolerance - When run in a counterclockwise direction (right-hand cut) spiral fluted tools evacuate chips up and out of the cut to reduce clogging. Round shanks allow use with a wide variety of toolholding systems. 06875-inches thread length. High-speed steel tools are good for most general purpose applications, offering a combination of hardness and toughness for wear resistance. Black oxide treatment adds lubricity and creates small pockets on the surface of the tool that act to hold coolant near the cutting edge.

 

YG-1 C2 Series Vanadium Alloy HSS Spiral Flute Tap Steam Oxide Round Shank with Square End Bottoming Chamfer 38-24 Thread Size H3 Tolerance

YG-1 C2 Series Vanadium Alloy HSS Spiral Flute Tap, Steam Oxide, Round Shank with Square End, Bottoming Chamfer, 3/8″-24 Thread Size, H3 Tolerance

YG-1 C2 Series Vanadium Alloy HSS Spiral Flute Tap, Steam Oxide, Round Shank with Square End, Bottoming Chamfer, 3/8″-24 Thread Size, H3 Tolerance - High-speed steel tools are good for most general purpose applications, offering a combination of hardness and toughness for wear resistance. 125-inches thread length. When run in a counterclockwise direction (right-hand cut) spiral fluted tools evacuate chips up and out of the cut to reduce clogging. Round shanks allow use with a wide variety of toolholding systems. Black oxide treatment adds lubricity and creates small pockets on the surface of the tool that act to hold coolant near the cutting edge.

 

YG-1 F8 Series Vanadium Alloy HSS Spiral Flute Tap TiN Coated Round Shank with Square End Bottoming Chamfer 12-20 Thread Size H5 Tolerance

YG-1 F8 Series Vanadium Alloy HSS Spiral Flute Tap, TiN Coated, Round Shank with Square End, Bottoming Chamfer, 1/2″-20 Thread Size, H5 Tolerance

YG-1 F8 Series Vanadium Alloy HSS Spiral Flute Tap, TiN Coated, Round Shank with Square End, Bottoming Chamfer, 1/2″-20 Thread Size, H5 Tolerance - Titanium nitride coatings add a hard layer of gold-colored ceramic to the surface that extends tool life and permits faster cutting speeds than uncoated tools. Round shanks allow use with a wide variety of toolholding systems. High-speed steel tools are good for most general purpose applications, offering a combination of hardness and toughness for wear resistance. 09375-inches thread length. When run in a counterclockwise direction (right-hand cut) spiral fluted tools evacuate chips up and out of the cut to reduce clogging.

 

YG-1 F4 Series Vanadium Alloy HSS Spiral Flute Tap Steam Oxide Round Shank with Square End Bottoming Chamfer 716-20 Thread Size H5 Tolerance

YG-1 F4 Series Vanadium Alloy HSS Spiral Flute Tap, Steam Oxide, Round Shank with Square End, Bottoming Chamfer, 7/16″-20 Thread Size, H5 Tolerance

YG-1 F4 Series Vanadium Alloy HSS Spiral Flute Tap, Steam Oxide, Round Shank with Square End, Bottoming Chamfer, 7/16″-20 Thread Size, H5 Tolerance - High-speed steel tools are good for most general purpose applications, offering a combination of hardness and toughness for wear resistance. Black oxide treatment adds lubricity and creates small pockets on the surface of the tool that act to hold coolant near the cutting edge. When run in a counterclockwise direction (right-hand cut) spiral fluted tools evacuate chips up and out of the cut to reduce clogging. Round shanks allow use with a wide variety of toolholding systems. 0875-inches thread length.

 

Drill America 516-18 High Speed Steel 2 Flute Spiral Point Tap TA Series

Drill America 5/16″-18 High Speed Steel 2 Flute Spiral Point Tap, T/A Series

Drill America 5/16″-18 High Speed Steel 2 Flute Spiral Point Tap, T/A Series - Straight flute tools allow chips to collect in the flutes as they cut and are well suited for most applications in shallow cuts. Uncoated tools feature just the base substrate without any additional treatment or coatings and are suitable for a wide range of applications. Right-hand cut tools have a cutting action that engages when they are run in a clockwise direction. Round shank with square end. High-speed steel tools are good for most general purpose applications, offering a combination of hardness and toughness for wear resistance.

 

Rocaris 5 Pcs M3 M4 M5 M6 M8 Titanium Coated HSS Spiral Flute Metric Taps Set

Rocaris 5 Pcs M3 M4 M5 M6 M8 Titanium Coated HSS Spiral Flute Metric Taps Set

Rocaris 5 Pcs M3 M4 M5 M6 M8 Titanium Coated HSS Spiral Flute Metric Taps Set - High hardness, fast cutting, wear high temperature. Sticky materials processing. Spiral groove is conducive to remove crumbs, not easily broken tap. Spiral tap the crumbs into a spiral up chip evacuation, it is more suitable for the processing of blind holes and.

 

YG-1 BS Series Vanadium Alloy HSS Spiral Flute Tap Steam Oxide Round Shank with Square End Modified Bottoming Chamfer M80-125 Thread Size D5 Tolerance

YG-1 BS Series Vanadium Alloy HSS Spiral Flute Tap, Steam Oxide, Round Shank with Square End, Modified Bottoming Chamfer, M8.0-1.25 Thread Size, D5 Tolerance

YG-1 BS Series Vanadium Alloy HSS Spiral Flute Tap, Steam Oxide, Round Shank with Square End, Modified Bottoming Chamfer, M8.0-1.25 Thread Size, D5 Tolerance - Black oxide treatment adds lubricity and creates small pockets on the surface of the tool that act to hold coolant near the cutting edge. 0472-inches thread length. When run in a counterclockwise direction (right-hand cut) spiral fluted tools evacuate chips up and out of the cut to reduce clogging. Round shanks allow use with a wide variety of toolholding systems. High-speed steel tools are good for most general purpose applications, offering a combination of hardness and toughness for wear resistance.

 

YG-1 F1 Series Vanadium Alloy HSS Spiral Flute Tap Uncoated Bright Finish Round Shank with Square End Modified Bottoming Chamfer M3-05 Thread Size D3 Tolerance

YG-1 F1 Series Vanadium Alloy HSS Spiral Flute Tap, Uncoated (Bright) Finish, Round Shank with Square End, Modified Bottoming Chamfer, M3-0.5 Thread Size, D3 Tolerance

YG-1 F1 Series Vanadium Alloy HSS Spiral Flute Tap, Uncoated (Bright) Finish, Round Shank with Square End, Modified Bottoming Chamfer, M3-0.5 Thread Size, D3 Tolerance - Uncoated tools feature just the base substrate without any additional treatment or coatings and are suitable for a wide range of applications. Round shanks allow use with a wide variety of toolholding systems. When run in a counterclockwise direction (right-hand cut) spiral fluted tools evacuate chips up and out of the cut to reduce clogging. High-speed steel tools are good for most general purpose applications, offering a combination of hardness and toughness for wear resistance. 0197-inches thread length.

 

Greenfield Threading 367909 GTVTD 14-20NC SFGP H3 3FL Plug Fast Spiral Flute Tap

Greenfield Threading 367909 GT/VTD 1/4-20NC SFGP H3 3FL Plug Fast Spiral Flute Tap

Greenfield Threading 367909 GT/VTD 1/4-20NC SFGP H3 3FL Plug Fast Spiral Flute Tap - 5000-inch, overall length (metric) 63. 3900-inch. 50mm, shank size 0. Hand of spiral right. 94mm, shank square size 0. Number of flutes 3, shank configuration straight with square. Thread creation thread cutting. Overall length 2. Hand of cut right. Surface condition bright, tap blank construction uscti table 302a, tap chamfer plug, tap construction high helix, tap ground threads yes, tap interrupted thread no, tap limit h3, tap style spiral flute tap, tap truncated threads no, tap type machine tap. 48mm, shank square length 0. Depth of cut 2xd. 2500-inch. 2550-inch, shank size (metric) 6. Diameter 0. Material application- n non-ferrous metal, p steel. Helix angle 52 degree. Operation type bottoming hole, tap spiral point no. Tool size 1/4, 20 unc. Material hss. 3125-inch, shank square length (metric) 7. Flute type spiral. 85mm, tap neck length 0. 1910-inch, shank square size (metric) 4.

 

INHDBOX 5 Pcs M3 M4 M5 M6 M8 Titanium Coated HSS Spiral Flute Metric Taps Set

INHDBOX 5 Pcs M3 M4 M5 M6 M8 Titanium Coated HSS Spiral Flute Metric Taps Set

INHDBOX 5 Pcs M3 M4 M5 M6 M8 Titanium Coated HSS Spiral Flute Metric Taps Set - Spiral tap the crumbs into a spiral up chip evacuation, it is more suitable for the processing of blind holes and. Spiral groove is conducive to remove crumbs, not easily broken tap. Sticky materials processing. 100% brand new and high quantity. High hardness, fast cutting, wear high temperature.





We are a participant in the Amazon Services LLC Associates Program, an affiliate advertising program designed to provide a means for us to earn fees by linking to Amazon.com and affiliated sites.